N415-0156 APR 11/07 NAPOLEON APPLIANCE CORPORATION.,214 BAYVIEW DR., BARRIE, ONTARIO, CANADA L4N 4Y8 PHONE: (705)726-4278FAX: (705)725-2564 EMAIL
10ORDERING REPLACEMENT PARTSBefore contacting the customer service department, check the NAC web site for more extensive cleaning, maintenance,trouble
11ASSEMBLY INSTRUCTIONSCAUTION: During unpacking and assembly it is recommended that you wear work glovesand safety glasses for your protection. Alth
1216 XN570-0073 (1/4-20 X 3/8”)3/816 XN450-0027 (1/4-20)Caster/Bracket Installation Attach (4) casters, using (4) 1/4 - 20 X 3/8” screws and (4) 1/4-2
134 XN570-0080 (#14 X 1/2")3/84Left and Right Cart Panel InstallationInstall end cart panels ensuring slots in panel are to the top, rest panel o
14PROPANE ONLY6Rotate basket slightly to allow wire to enter the holes in the side panel. Pushthrough and upwards, rotating to allow the bend in the
15Front Cabinet Support Installation7Fasten top rail assembly to the front of side panels using (4) #14 x 1/2” screws.For ease of installation start a
16TWO PEOPLE ARE REQUIREDFOR THIS STEP6 xN570-0073 (1/4-20 x 3/8”)3/89Lift grill head and place on assembled cart, lining up holes in top of side cart
1711Insert (4) 1/4-20 x 5/8” screws through washers into threaded holes in side ofbase, do not tighten all the way. Slide assembled side shelf over s
18Side Burner Installation4 XN570-0082 (1/4-20 X 5/8")3/812Insert (4)1/4-20 x 5/8” screws through washers into threaded holes in side of base.Do
193/84 x N570-0073(1/4-20 X 3/8")13Cabinet Door InstallationInsert pivot rod through hole on inside top of door. Holding door in one hand,direc
2NAPOLEON products are designed with superior components and materials, and are assembled by trainedcraftsmen who take great pride in their work. The
203 X N305-005714Insert sear plates into base, position one over each tube burner with slots downto allow drippings to travel through.Postion grills a
21Grease Tray and Holder Installation16Clip the wire grease tray holder into the two holes located in the center of theback panel. Place the aluminum
22CLIP HOSE TO SIDE PANEL USINGHOSE RETAINER CLIP SUPPLIEDPROPANE ONLY3/42 XNATURAL GAS ONLY1xN105-0002CLIP HOSE TO SIDE PANEL USING HOSERETAINER CLIP
23A LEAK TEST MUST BE PERFORMED AT THEFOLLOWING TIMES:•BEFORE INITIAL USE EVEN IF THE GRILL WASDEALER ASSEMBLED.•AT LEAST ONCE PER YEAR.•WHENEVER ANY
24Item Part # Description 4851 N135-0024K left side lid casting x2 N385-0129 NAPOLEON logo x3 W450-0005 logo spring clips x4 N510-0010 black silicone
25Item Part # Description 485N010-0508 manifold assembly c/w valves n42 N720-0044 manifold flex connector x43 N255-0027 union fitting 3/8" - 3/8
28NOTES
3SAFETY PRECAUTIONSDo not store or use gasoline or other flam-mable liquids or vapor in the vicinity of thisor any other appliance. An L.P. cylinder
4NATURAL GAS HOOK-UP: This natural gas grill is supplied with a 10ft supply hose (complete with a quick disconnect)designed for natural gas and certi
5LEFT BURNERSIDE BURNEROPEN LID.ENSURING BURNER CONTROLSARE IN THE OFF POSITION, TURNON THE GAS SUPPLY VALVE.CENTER BURNERLIGHTING INSTRUCTIONSRIGHT B
6OPERATING THE GRILLBURN IN PROCEDUREWhen lit for the first time, the gas grill will emit a slight odour. This is a normal temporary condition caused
7If the burner is getting too little air, the flames will be lazy yellow, and possibly produce soot. If the burner is getting toomuch air, the flames
8 TUBE BURNER - The burner is made from heavy wall 304 stainless steel, but due to the extreme heat and corrosiveenvironment, surface corrosion will o
9Problem Possible Causes SolutionLow heat / Low flame whenvalve turned to high.For propane - improper lightingprocedure.Ensure lighting procedure is f
Commentaires sur ces manuels