Napoleon-grills Gourmet Grills BIU405 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Grilles Napoleon-grills Gourmet Grills BIU405. Napoleon Grills Gourmet Grills BIU405 Manuel d'utilisation Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 18
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
BUILT-IN UNIT INSTRUCTION GUIDE
N415-0175 / JAN 02/08
Please use this manual in conjunction with your main manual to properly assemble your built-in grill. Refer to
the main manual for operating, cleaning, and maintenance instructions. This grill is designed for NON-COM-
BUSTIBLE enclosures only, and must be installed and serviced by a qualified installer to local codes.
BUILT IN PROPANE GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and piping should be located as
shown in the built-in instructions. Do not use hose to connect the unit. It must be connected with either rigid pipe, copper tube or an
approved flexible metal connector. The installation must comply with CAN B149.1 Natural Gas and Propane installation code in
Canada, or to the National Fuel Gas code, ANSI Z223.1 in the United States. The minimum recommended piping size is NPS 1/2"
for rigid pipe, and 1/2" OD for copper tubing (based on a 20 ft run). Longer runs may require larger sizes to conform with local codes
or to conform with CAN B149.1. Propane Gas Installation Code in Canada or to the National Fuel Gas Code, ANSI Z223.1 in the
United States. The gas supply must be connected to the 3/8” flare elbow fitting located under the right hand side of the control panel.
If installing a side burner, a separate line must be branched off to the side burner unit and enter the side burner opening at the
specified location. If the enclosure is to house a propane cylinder, the tank portion of the enclosure must be ventilated according to
local codes, and must not have communication with the cavity used to enclose the gas grill. A propane tank can not be stored below
the gas grill.
BUILT IN NATURAL GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and piping should be located as
shown in the built-in instructions. Do not use hose to connect the unit. It must be connected with either rigid pipe, copper tube or an
approved flexible metal connector. The installation must comply with CAN B149.1 Natural Gas and Propane Installation Code in
Canada, or to the National Fuel Gas Code, ANSI Z223.1 in the United States. The minimum recommended piping size is NPS 1/2"
for rigid pipe, and 5/8" OD for copper tubing (based on a 20 ft run). Longer runs may require larger sizes to conform with local codes
or to conform with CAN B149.1. Natural Gas Installation Code in Canada or to the National Fuel Gas Code, ANSI Z223.1 in the
United States.
Built in units are supplied with a drip pan which holds only a minimal amount of grease. To prevent grease fires, the pan must
be cleaned after each use.
SERIAL #______________________
DANGER: READ ALL INSTRUCTIONS CAREFULLY BEFORE OPERATING GRILL. FAILURE TO FOLLOW
THESE INSTRUCTIONS EXACTLY COULD RESULT IN A FIRE CAUSING SERIOUS INJURY OR DEATH.
Vue de la page 0
1 2 3 4 5 6 ... 17 18

Résumé du contenu

Page 1 - N415-0175 / JAN 02/08

BUILT-IN UNIT INSTRUCTION GUIDEN415-0175 / JAN 02/08Please use this manual in conjunction with your main manual to properly assemble your built-in gri

Page 2 - NON-COMBUSTIBLE MATERIAL

SERIAL #______________________GUIDE D’INSTRUCTIONS POUR LES GRILS ENCASTRÉSVeuillez utiliser ce guide conjointement avec votre manuel principal pour a

Page 3

BIPT450 29 1/2” 20 5/8” 8 7/8”BIPT600 37 3/4” 20 5/8” 8 7/8”BIPT750 49 3/4” 20 5/8” 9 5/8”BIU405 271/2” 16 3/4” 12”

Page 4

HLPLE CADRE DES ACCESSOIRESCHEVAUCHE L’OUVERTURE DE 1 ½”SUR LES QUATRE CÔTÉS.N° de pièceDescriptionIllustrationLHN370-0070Porte horizontale peinteN370

Page 5

1. INSTRUCTIONS POUR LE GRIL ENCASTRÉ BIPT450N010-0568N715-0080N080-0213N080-0213N570-0026Ce gril est conçu pour des cabinets INCOMBUSTIBLES OU EN MAÇ

Page 6

2. INSTRUCTIONS POUR LE GRIL ENCASTRÉ BIPT600N080-0213N715-0081N010-0569N080-0213N570-0026N380-0009N051-0001Ce gril est conçu pour des cabinets INCOMB

Page 7

3. INSTRUCTIONS POUR LE GRIL ENCASTRÉ BIPT750N715-0082N010-0570N080-0213N570-0026N380-0009N051-0001N080-0213Ce gril est conçu pour des cabinets INCOM

Page 8 - N280-0004 (STN STL)

4. INSTRUCTIONS POUR LE GRIL ENCASTRÉ BIU405N080-0215N570-0026N080-0215N570-0026N715-0083N080-0155N080-015523 e c-cN570-0026Ce gril est conçu pour d

Page 9

5. INSTRUCTIONS POUR LE BRÛLEUR LATÉRAL ENCASTRÉN280-0003P (NOIR)N280-0004 (ACIER INOX.)l. Placez le cadre du brûleur latéral dans l’ouverture. Le cad

Page 10

6. INSTRUCTIONS D’INSTALLATION DES TIROIRS7. INSTRUCTIONS D’INSTALLATION DES PORTES1. Déballez le cadre et la porte.a. Pour les portes cambrées en ac

Page 11 - MATÉRIAU INCOMBUSTIBLE

BIPT450 29 1/2” 20 5/8” 8 7/8”BIPT600 37 3/4” 20 5/8” 8 7/8”BIPT750 49 3/4” 20 5/8” 9 5/8”BIU405 271/2” 16 3/4” 12

Page 12 - SUR LES QUATRE CÔTÉS

HWDNOTE: ACCESSORY FRAMES OVERLAPOPENING BY 1 ½” ON ALL 4 SIDESPart #DescriptionPictureWHN370-0070Flat horizontal painted doorN370-0357SSN370-0358SS13

Page 13 - N570-0026

1. BIPT450 BUILT-IN INSTRUCTIONSThis grill is designed for MASONRY, NON-COMBUSTIBLE enclosures only, and must be installed and serviced by a qualified

Page 14

2. BIPT600 BUILT-IN INSTRUCTIONSThis grill is designed for MASONRY, NON-COMBUSTIBLE enclosures only, and must be installed and serviced by a qualified

Page 15

3. BIPT750 BUILT-IN INSTRUCTIONSThis grill is designed for MASONRY, NON-COMBUSTIBLE enclosures only, and must be installed and serviced by a qualified

Page 16 - 23 e c-c

4. BIU405 BUILT-IN INSTRUCTIONSN080-0215N570-0026N080-0215N570-0026N715-0083N080-0155N080-015523 e c-cThis grill is designed for MASONRY, NON-COMBUS

Page 17 - N280-0004 (ACIER INOX.)

1. Fit the side burner frame into the opening. The frame should be attached to the opening to prevent any future movement (fasten-ers not included).2

Page 18

6. BUILT-IN ACCESSORY DRAWER INSTRUCTIONS7. BUILT-IN ACCESSORY DOOR INSTRUCTIONS1. Unpack the drawer frame assembly.2. Remove the drawers from the enc

Commentaires sur ces manuels

Pas de commentaire